9200iw plus manual

Shipping Calculator. If you have a question about the product specifications or the functionality of the lamp, please type it in here and contribute to the MPL community. If you have a question related to price or shipping please contact our helpful, accountable Customer Service.

Search for the projector lamp you need! CB1 BL-FPD BL-FPA BL-FPA BL-FSC CPI DE. Save this page directly to your inbox! Add to Cart. Added to Cart. Alternative Lamp ID's 3M Do you have a question about this product? Does this module match my projector? See "Suitable Projectors" Above.

Is it as good as the bulb that came with my projector originally? It is exactly the same quality, it is not an imitation lamp. If I buy this item and find out it is the wrong item or doesn't work for any reason, can I get an exchange or refund? Write a review. We're sorry, but we have encountered the following issue s :. Please send me an email when my review is posted. Recommend product Yes No. Page 2 This page intentionally left blank for printed version Page 3 Introduction Page 4 Risoluzioni dei problemi Page 6 Menu System Menu Navigation Page 7: Introduction Before operating this machine, please read the entire manual thoroughly.

The 3M Digital Wall Display Systems are designed, built, and tested for use indoors, using 3M lamps, 3M mount hardware, and nominal local voltages. Service should only be performed by a 3M authorized service provider.

Aside from the projection lamp assembly, there are no serviceable parts inside the unit. Page Product Safety Label U. Page Fcc Statement-Class A If normal coaxial cables are used, the cable must be enclosed in metal pipes or in a similar way to reduce the interference noise radiation.

Video Inputs The input signal amplitude must not exceed the specified level. See Appendix for these levels. After the 3M Digital Wall Display has been installed in your meeting room, you are ready to set it up.

Please read this guide thoroughly before operating your new 3M Digital Wall Display. Be sure to check our web site www. The AC power cord supplied with the unit is 6 feet 2 m long. Remove the accessory box es from the top support. Remove the top support. Remove the plastic bag from the 3M Digital Wall Display by lifting the top of the unit and pushing the bag towards the bottom of the unit.

Then set down the top. If possible, position the 3M Digital Wall Display and shipping tray in front of the wall where the bracket is located. Position the unit so that the projection arm is closest to the wall. Page Operation 1. Plug power cord into wall socket.

This should stay on at all times. Now the 3M Digital Wall Display is in standby mode. The fan will continue to run for approximately five minutes to cool the unit. The distance between the sensor and remote control must be shorter than 4 meters 13 feet. The remote control unit has two keypads. The Forward keypad is above the flip-top cover.

The Rear keypad is beneath the cover. When power is turned on, the 3M Digital Wall Display will automatically extend the projection arm and ignite the lamp.

Mute Press to temporarily turn off the sound. Page Installing Or Replacing Batteries 3. Snap the battery compartment cover back on. Note: Avoid excessive heat and humidity. Do not mix old and new batteries or different types of batteries.

Note: Recycle or dispose of batteries per local and regional regulations. These signals are created and transmitted by small sensors near the ends of the battery-powered marker sleeves.

Page Assembling Digital Eraser The digital eraser erases marker input by sending signals from the digital eraser in the same way as the digital markers.

Page Menu System Most adjustments and settings are available in the main menu and sub-menus. Use the Menu Keypad arrow buttons or the Direction Knob to move through the menu.

Click the Trigger button to change a menu item. No computer is needed to run this system. This mode should be used without projection. Standard dry-erase cleaners may be used on the dry-erasable screens, such as Sanford Page Lamp Replacement 5.

Two black wires connect to the lamp cartridge by a black plastic receptacle on the right side of the lamp cartridge. Page 38 8. Holding the latch open, slide the new lamp cartridge into place. Reconnect black wires to the receptacle.